EINHELL RT-TS 1725/1 U Instrucciones de operaciones descargar pdf (Pagina 31)

 The laser beam can be blocked by deposits of

dust and chips. You should therefore remove

these particles from the laser emission aperture

each time after you use the laser (equipment off).

 Notes on batteries: If you do not intend to use the

laser for a lengthy period of time, remove the

batteries from the battery compartment. Any

leakage of battery fluid might damage the tool.

 Do not place the batteries on heaters or expose

them to direct sunshine for long periods;

temperatures in excess of 50°C may damage the

tool.

8.10 Adjusting the laser (Fig. 35)

If the laser (34) ceases to indicate the correct cutting

line, you can readjust the laser. To do so, open the

screws (z) and set the laser by moving sideways to

that the laser beam strikes the teeth of the saw blade

(5).

9. Functions

Important!!

 After every new adjustment we recommend you

to make a trial cut in order to check the new

settings.

 After switching on the saw, wait for the blade to

reach its maximum speed of rotation before

commencing with the cut.

 Take extra care when starting the cut!

 Never use the equipment without the suction

function.

 Regularly check and clean the suction channels.

9.1 Making longitudinal cuts (Figure 39)

Longitudinal cutting (also known as slitting) is when

you use the saw to cut along the grain of the wood.

Press one edge of the workpiece against the parallel

stop (7) while the flat side lies on the saw table (1).

The blade guard (2) must always be lowered over the

workpiece.

When you make a longitudinal cut, never adopt a

working position that is in line with the cutting

direction.

 Set the parallel stop (7) in accordance with the

workpiece height and the desired width. (See

9.4.)

 Switch on the saw.

 Place your hands (with fingers closed) flat on the

workpiece and push the workpiece along the

parallel stop (7) and into the blade (5).

 Guide at the side with your left or right hand

(depending on the position of the parallel stop)

only as far as the front edge of the saw blade

guard (2).

 Always push the workpiece through to the end of

the splitter (4).

 The offcut piece remains on the saw table (1) until

the blade (5) is back in its position of rest.

 Secure long workpieces against falling off at the

end of the cut (e.g. with a roller stand etc.) (e.g.

roller table etc.)

9.1.1 Cutting narrow workpieces (Fig. 40)

Be sure

to use a push stick (17) when making

longitudinal cuts in workpieces smaller than 120 mm

in width. A push block is supplied with the saw!

Replace a worn or damaged push stick

immediately.

9.1.2 Cutting very narrow workpieces

(Fig. 41)

 Be sure to use a push block when making

longitudinal cuts in very narrow workpieces with a

width of 30 mm and less.

 The low guide face of the parallel stop is best

used in this case.

 There is no push block supplied with the

saw! (Available from your specialist dealer)

Replace the push block without delay when it

becomes worn.

9.1.3 Making angular cuts (Fig. 42)

Angular cuts must always be made using the parallel

stop (7).

 Set the blade (5) to the desired angle. (See 9.3.)

 Set the parallel stop (7) in accordance with the

workpiece width and height (see 9.3)

 Carry out the cut in accordance with the

workpiece width (see 10.1.1 and 10.1.2).

9.2 Making cross cuts (Fig. 31,43)

 Slide the cross stop (13) into one of the grooves

(32) in the table and adjust to the required angle.

(see 9.6). If you also want to tilt the blade (5), use

the groove (32) which prevents your hand and the

cross stop from making contact with the blade

guard.

 If necessary, use the stop rail (e).

 Press the workpiece firmly against the cross stop

(13).

 Switch on the saw.

 Push the cross stop (13) and the workpiece

toward the blade in order to make the cut.

 Important:

Always hold the guided part of the

workpiece. Never hold the part which is to be

cut off.

 Push the cross stop (13) forward until the

workpiece is cut all the way through.

 Switch off the saw again. Do not remove the

Anleitung_RT_TS_1725_1_U_SPK1:_ 28.10.2011 8:45 Uhr Seite 31

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 131 132

Comentarios a estos manuales

Sin comentarios

EINHELL RT-TS 1725/1 U Instrucciones de operaciones Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Sierras circulares EINHELL RT-TS 1725/1 U